Bendpak HD-9AE

Description:
 
Slip plates: Free-floating alignments made easy-to-handle to help work without delay. Multi-caster slip plates positioned in the rear, with turn plates in front, allowing for precise alignments.
 
Turn plate: Corrosion-resistant galvanized turn plates easily positioned using BendPak’s turn plate pockets. These dual recessed turn plate pockets get your turn plates in the precise spot they need to be.
 
Dual-hub cable sheaves:  10.5” diameter cable sheaves within the runway, cross tubes and 2.25” diameter sheave axles.
 
Heavy-duty aircraft cable: 1/2” diameter 6 x 25 aircraft-quality stainless-steel lifting cables routed internally through the post structures.
 
Adjustable height locking positions: Lift turn plates above eye level or take them down a few notches to help roll your wheels or set your 3D alignment pads. Each height position automatically locks in places and releases with the push of a button.
 
Built-in lubrication: Grease fittings are standard on all BendPak lifts. Keep your cable sheaves greased and the cables running smoothly.
 
Flow restrictor: Hydraulic flow dividers offer the total confidence that even in a worst-case scenario, your alignment lift is incapable of crashing to the floor. They also guarantee level ascents and descents with each use.
 
Spring-loaded safety locks: Durable springs facilitate lock engagement as the lift platform ascends over each ladder position. Even if your garage floor has a slight slope, the spring-loaded locks will accommodate for the tilt and keep your rise even at all times.
 
Push-button pneumatic lock release: The pneumatic lock release instantly releases all four locks in a single, simultaneous motion.
 
Secondary lock system: A secondary lock system detects cable slack and stops all lift functions the second slack is detected.
 
Electric-hydraulic power system: Electric-hydraulic power system features an easy-to-read, ergonomic display.
 
Longer approach ramps: Ramps are extended to provide easy access to large and small vehicles alike.
 
Flexible protective conduit: Thick, tough, rubber conduit protects all airlines and hydraulic hoses. The material is non-conducive and resistant to chemicals and oil.
 
 
Specifications:
 
   -Capacity:
      Lifting Capacity: 9,000 lbs. (4,082 kg)
      Max Capacity / Front Axle: 4,500 lbs. (2,041 kg)
      Max Capacity / Rear Axle: 4,500 lbs. (2,041 kg)
 
   -Rise:
      (A) - Min. Runway Height: 7" (178 mm)
      (B) - Max. Rise: 70" (1,778 mm)
      (C) - Max. Lifting Height: 76.9" (1,953 mm)
      Time to Full Rise: 60 seconds
 
   -Outside Dimensions:
      (D) - Overall Width: 127" (3,226 mm)
      (E) - Outside Length: 198" (5,029 mm)
      (F) - Overall Length: 224.25" (5,696 mm)
      (G) - Height of Columns: 88" (2,235 mm)
 
   -Inside Dimensions:
      (H) - Width Between Columns: 117" (2,972 mm)
      (I) - Drive-Thru Clearance: 103.5" (2,629 mm)
 
   -Runways:
      (J) - Runway Width: 19" (483 mm)
      (K) - Length of Runways: 181.75" (4,616 mm)
      (L) - Width Between Runways: 37" (940 mm)
 
   -Alignment:
      (M) - Min. 4-Wheel Alignment: 71" (1,803 mm)
      (N) - Max. 4-Wheel Alignment: 145" (3,683 mm)
      (O) - Max. 2-Wheel Alignment: 160" (4,064 mm)
 
   -Minimum Wheelbase:
      Rated Capacity: 135" (3,429 mm)
      75% Capacity: 115" (2,921 mm)
      50% Capacity: 95" (2,413 mm)
      25% Capacity: 80" (2,032 mm)
 
   -Locking:
      Locking Positions: 14
      Lock Spacing: 4
 
   -Power Unit:
      Motor: 220 VAC / 60 Hz / 1 Ph
      Noise: 45 dB
 
   -Shipping:
      Weight: 2,276 lbs. (1,032 kg)
      Dimensions: 190'' x 22'' x 30'' (4,826 mm x 558 mm x 762 mm)
 
Note: An air supply (minimum: 30 psi / 3 CFM) is required for the safety-lock mechanisms to disengage. It is solely the responsibility of the end-user to provide, install and maintain the air supply.
 
 
WARNING: Cancer and reproductive harm - www.P65Warnings.ca.gov